Huawei MA5620 configuration Broadband and Voice example

Huawei EPON configuration example

1. Serial user name and password root/mduadmin is used in public part and broadband PPPOE part.

MA5620E > enable

MA5620E#config

MA5620E (config) #

MA5620E (config) # sysname bigcow / name the device / * before the public part

First, build vlan and address

Bigcow (config) # vlan 100 / build the management vlan/ of onu

Bigcow (config) # vlan 3001 to 3016 / pppoe vlan/ bigcow for this onu (config) # port vlan 100Let0 1 / allow upstream vlan/

Bigcow (config) # port vlan 3001 to 3016 lap 0 1 / allow pppoe vlan/

Note: the vlan used by onu itself is transmitted through the uplink port, and the vlan used by the building switch does not need to be transmitted through.

Bigcow (config) # int vlan 100

Bigcow (config-if-vlanif100) # ip add 10.247.32.2 26 / build the management ip/ of onu

Bigcow (config-if-vlanif100) # quit step down

Bigcow (config) # ip route 0.0.0.0 0.0.0.0 10.247.32.1

Second, set up user pvc in dialing and passing through

Bigcow (config) # undo service-port all first delete the first 13 eth ports of pvc for pppoe,14, 15 and 16 ports for cascaded building switches

Bigcow (config) #

Service-port vlan 3001 eth 0/1/1 user-vlan untagged rx-cttr 6 tx-cttr 6

Service-port vlan 3002 eth 0/1/2 user-vlan untagged rx-cttr 6 tx-cttr 6

Service-port vlan 3003 eth 0/1/3 user-vlan untagged rx-cttr 6 tx-cttr 6

Service-port vlan 3004 eth 0/1/4 user-vlan untagged rx-cttr 6 tx-cttr 6

Service-port vlan 3005 eth 0/1/5 user-vlan untagged rx-cttr 6 tx-cttr 6

Service-port vlan 3006 eth 0/1/6 user-vlan untagged rx-cttr 6 tx-cttr 6

Service-port vlan 3007 eth 0/1/7 user-vlan untagged rx-cttr 6 tx-cttr 6

Service-port vlan 3008 eth 0/1/8 user-vlan untagged rx-cttr 6 tx-cttr 6

Service-port vlan 3009 eth 0/1/9 user-vlan untagged rx-cttr 6 tx-cttr 6

Service-port vlan 3010 eth 0/1/10 user-vlan untagged rx-cttr 6 tx-cttr 6

Service-port vlan 3011 eth 0/1/11 user-vlan untagged rx-cttr 6 tx-cttr 6

Service-port vlan 3012 eth 0/1/12 user-vlan untagged rx-cttr 6 tx-cttr 6

Service-port vlan 3013 eth 0/1/13 user-vlan untagged rx-cttr 6 tx-cttr 6

Transmission port

(config) # service-port vlan transparent eth 0 other-all rx-cttr 1 other-all rx-cttr 6 tx-cttr 6

(config) # service-port vlan transparent eth 0 other-all rx-cttr 1 15 other-all rx-cttr 6 tx-cttr 6

(config) # service-port vlan transparent eth 0 other-all rx-cttr 1 16 other-all rx-cttr 6 tx-cttr 6

Finally save and exit

Bigcow (config) # save

Bigcow (config) # quit

2. Phone part configuration

(config) # voip

(config-voip) # ip address media 10.247.32.2 10.247.32.1 / the previous address is managed by this device

Address, followed by the gateway address, that is, the two addresses will change according to the actual address.

(config-voip) # ip address signaling 10.247.32.2 / this device management address, the address will change / (config) # interface h348 0

(config-if-h348-0) # if-h348 attribute mgip 10.247.32.2 mgport 2944 transfer udp

/ this device management address, the address will change /

(config-if-h348-0) # if-h348 attribute mgcip_1 58.242.3.158 mgcport_1 2944 / fixed address /

(config-if-h348-0) # if-h348 attribute mgcip_2 58.242.3.186 mgcport_2 2944 / fixed address /

(config-if-h348-0) # if-h348 attribute mg-media-ip 10.247.32.2 / this device management address, the address will change /

(config-if-h348-0) # if-h348 attribute start-negotiate-version 2

(config-if-h348-0) # mg-software parameter 2 2 / Startup double attribution, corresponding to core /

(config-if-h348-0) # reset coldstart

(config) # esl user / associated subscriber line /

(config-esluser) # mgpstnuser batadd 0 terminalid 0 (config) 2, 10, 10, 2, 10, 10, 10, 10, 10, 10, 10, 10, 10, 2, 10, 10, 2, 10, 2, 10, 2, 10, 2, 2, 10, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 2, 10, 2, 10, 2, 10, 2, 10, 2, 10, 2, 10, 2, 10

# save