CCNA Lab 2: manually establishing static routing tables
HQ > en
HQ > enable
HQ#conf t
Enter configuration commands, one per line. End with CNTL/Z.
HQ (config) # int e0Universe 0
HQ (config-if) # no shut
HQ (config-if) # no shutdown
HQ (config-if) # ip add
HQ (config-if) # ip address 172.16.1.100 255.255.255.248
HQ (config-if) # exi
HQ (config) # int e0bin1
HQ (config-if) # no shu
HQ (config-if) # no shutdown
HQ (config-if) # ip ad
HQ (config-if) # ip add
HQ (config-if) # ip address 192.168.1.2 255.255.255.252
HQ (config-if) # exi
HQ (config) # exi
* Sep 14 16 Configured from console by console 38 Fran 30.401:% SYS-5-CONFIG_I: Configured from console by console
HQ#show ip route / / Show routing tabl
Codes: l-local, C-connected, S-static, R-RIP, M-mobile, B-BGP
D-EIGRP, EX-EIGRP external, O-OSPF, IA-OSPF inter area
N1-OSPF NSSA external type 1, N2-OSPF NSSA external type 2
E1-OSPF external type 1, E2-OSPF external type 2
I-IS-IS, su-IS-IS summary, L1-IS-IS level-1, L2-IS-IS level-2
Ia-IS-IS inter area, *-candidate default, U-per-user static route
O-ODR, P-periodic downloaded static route, H-NHRP, l-LISP
A-application route
+-replicated route,%-next hop override
Gateway of last resort is not set
172.16.0.0/16 is variably subnetted, 2 subnets, 2 masks
C 172.16.1.96/29 is directly connected, Ethernet0/0
L 172.16.1.100/32 is directly connected, Ethernet0/0
192.168.1.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.1.0/30 is directly connected, Ethernet0/1
L 192.168.1.2/32 is directly connected, Ethernet0/1
HQ#conf t
Enter configuration commands, one per line. End with CNTL/Z.
HQ (config) # ip route 10.1.10.16 255.255.255.240 e0swap 1 / / put 10.1.10.16 in the routing table and communicate over e0max 1
HQ (config) # exi
HQ#
* Sep 14 16 Configured from console by console 59 race 32.032:% SYS-5-CONFIG_I: Configured from console by console
HQ#ping 10.1.10.23
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.1.10.23, timeout is 2 seconds:
.!
Success rate is 80 percent (4amp 5), round-trip min/avg/max = 1-1-1 ms / / ping destination address
HQ#show ip route / / displays the modified routing table
Codes: l-local, C-connected, S-static, R-RIP, M-mobile, B-BGP
D-EIGRP, EX-EIGRP external, O-OSPF, IA-OSPF inter area
N1-OSPF NSSA external type 1, N2-OSPF NSSA external type 2
E1-OSPF external type 1, E2-OSPF external type 2
I-IS-IS, su-IS-IS summary, L1-IS-IS level-1, L2-IS-IS level-2
Ia-IS-IS inter area, *-candidate default, U-per-user static route
O-ODR, P-periodic downloaded static route, H-NHRP, l-LISP
A-application route
+-replicated route,%-next hop override
Gateway of last resort is not set
10.0.0.0/28 is subnetted, 1 subnets
S 10.1.10.16 is directly connected, Ethernet0/1
172.16.0.0/16 is variably subnetted, 2 subnets, 2 masks
C 172.16.1.96/29 is directly connected, Ethernet0/0
L 172.16.1.100/32 is directly connected, Ethernet0/0
192.168.1.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.1.0/30 is directly connected, Ethernet0/1
L 192.168.1.2/32 is directly connected, Ethernet0/1
HQ#
With the same configuration on another router Branch, you can access each other. Pay attention to the mask.
Related settings:
HQ: e0/1 192.168.1.2 255.255.255.252
E0/0 172.16.1.100 255.255.255.248
Branch: e0/1 192.168.1.1 255.255.255.0
E0/0 10.1.10.23 255.255.255.240
Important command: show ip route displays routing table
Ip route + ip address + mask manually set static routing table
Note: when setting up the static routing table manually using the ip route + ip address + mask command, the ip address should be written here at the arrow, not the local ip address.
